PARTIAL
PARTS LIST FOR PROJECT JRS032610
Parts
List is for only one magnetic generator and is subject
to change.
Note: We do not have parts or magnets for sale. |
Quantity |
Description |
Estimated Cost |
6 |
 |
2" x 4" x 1/2" - N42
Neodymium Magnets
Magnetized through thickness |
$15.00 to $18.50 each
Plus shipping |
6 |
 |
3" x 1" x 1/2" - N42
Neodymium Magnets
Magnetized through thickness
Note: Some may prefer the arch magnets instead
but that is up to you as they cost more but generate
greater output. I suggest you use bar magnets for your
prototype. |
$7.00 to $9.50 each
Plus shipping |
11 |
 |
1/2" x 24" Stainless
Steel Rod or you may use a copper ground rod with a
steel core which is sold in most electrical supply
stores, where as stainless steel rods are available in
some hardware stores. |
$15.00 to $25.00 each
Bars usually come in
4' and 6' lengths
Plus shipping |
11 |
 |
PVC Pipe: 6" Inside
Diameter x 18" Length |
$10.00 to $15.00 per
12" Plus
shipping |
2 |
 |
PVC Pipe End Caps: 6" |
$15.00 to $25.00 each
Plus shipping |
1 |
 |
Magnet Wire 20 Gauge, 5 lbs. 1,575 ft.
6 primary 12" coils = 200 turns each |
$100.00 to $115.00
each
Plus shipping |
1 |
Magnet Wire
18
Gauge, 5 lbs. 1,000 ft.
12 Secondary 4"Coils = 150 turns each. |
$95.00 to $105.00
each
Plus shipping |
2 |
 |
24" x 24" x 1/4" or
one 1/2" x 24"x24" Plexiglas Sheet
You will be making an 18" x1/2" circle out of it, or you
may use something else as long as it's not wood, iron,
steel or aluminum. Plastic is fine and must be 1/2"
total thickness. |
$35.00 to $50.00 each
Plus shipping |
1 |
 |
1" wide, electrical tape. |
$2.50 to $3.50 each
Plus shipping |
4 |
 |
1" x 6" solid PVC or
plastic dowel rod, high strength, or optionally you can
use 1" high pressure PVC pipe. |
$3.00 to $6.00 each
Plus shipping |
1 |
1" x 6 ft. PVC high
pressure water pipe,
or best of all...Acetal
Bushing Stock |
$8.00 to $12.00 each
Plus shipping |
1 |
 |
1" x 1/2" x 48"
Acetal
Bushing Stock
(ideal for high strength) |
$12.00 to $14.00 per
foot
Plus shipping |
 |
Flanged
Pin and Shaft Coupler
Two 1/2" inside
diameter with 6" or greater outside diameter flange made
of aluminum. This is used to mount your 18" round stator
too.
Some shaft couplers come with a face plate/collar/ring
for the other side and then you do
NOT need to
buy two shaft couplers. |
$15.00 to $35.00 each
Plus shipping |
 |
Shaft
Bearing Kit
Two 1/2" inside
diameter shaft bearings..
These will be mounted dead center inside the PVC end
caps used to secure your 1/2" stainless steel axel.
There are different mounting styles, so be sure to get a
set that you know you can screw down inside the end
caps. |
$25.00 to $35.00 set
of 2
Plus shipping |
 |
General
Purpose Sandpaper
You want medium grit,
not fine as you will be using in to light sand down 3"
of the ends of the 6" PVC pipe. This makes is possible
to slide the end caps on and off without them getting
stuck on. And when they do, it's extremely hard to get
them back off. lol |
$5.00 to $7.00 pack
of 10
Plus shipping |
 |
1/2" Dremel Sanding
Drum Mandrel.
The Drum Mandrel
holds a Sanding Band covered with aluminum oxide
abrasive. Sanding Bands are sold separately.
This is a must have. This will be used to contour the
bottom of your
Acetal
Bushing Posts so they match the contour of the 6"
PVC pipe for a secure fit.
Don't forget to buy the sanding band that slips over the
drum. You should get several medium and several heavy
grit sanding bands. You will need a high speed bit or
Dremel tool to use this sanding drum. |
$7.00 to $12.00
Plus shipping |
 |
Two Speed Dremel .
The
Dremel 200 Series
rotary tool offers the precision and control required to
complete a wide range of projects. Its two speed
settings allow you to use the low speed setting for
cleaning applications (which I love) and using brush
accessories, and the high speed setting for routing,
cutting and sanding applications.
This is what you
need for your sanding drum. YOU can use a hand drill,
but most hand drills are NOT high speed.
|
$50.00 to $75.00
Plus shipping |
|
|
|
|